Interlogix Monitor XL Hardware Guide Manual de usuario Pagina 61
- Pagina / 66
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
22-0375 rev1.1 Monitor ISM/xL™ Hardware Guide 57
Appendix “C” Basic Circuit Types
Normally Closed Normally Closed with 2.2 K End of Line Resistor
NC
NOCOM
312
Yellow
Black
CABLE
1
I
n
p
u
t
I
n
p
u
t
2
C
O
M
Yellow
Black
Black
Yellow
NC
NO
COM
Black
NC
NOCOM
Yellow
Black
Yellow
Yellow
Black
Junction
Single Device
Multiple Device
C
NO
NC
C
NO
NC
2.2 K
NC
NOCOM
312
Yellow
Black
CABLE
1
I
n
p
u
t
I
n
p
u
t
2
C
O
M
C
NO
NC
Yellow
Black
• CAUTION: This circuit type supplies minimal supervision.
• The end of line resistor, must always be placed at the Device, NOT at
the Alarm Input.
• When the Contact is Open, the Control will see the 2.2K-ohm
resistor, which equals Alarm.
• If the loop wiring is Open (loss of resistor), the System will indicate a
Tamper condition.
• This Circuit Type cannot be used in a Multiple Device application.
• Each device using this alarm loop must be connected to 1 Alarm
Input only.
Sample use: Could be applied to a device alarm contact that would
ordinarily always be closed (e.g. a vibration detector). The 2.2K resistor is
not used. If the device is triggered in an off guard (unarmed) state and the
contact goes open, a tamper condition is transmitted because there is no
resistor. If the device is triggered in an on guard (armed) state, an alarm
condition is transmitted because there is no resistor.
Form "C" Single Resistor EOL Normally Open with EOL
NC
NOCOM
312
Red
Black
CABLE
1
I
n
p
u
t
I
n
p
u
t
2
C
O
M
C
NO
NC
Red
Black
C
NO
NC
Red
Black Black
Red
C
NO
NC
NC
NO COM
NC
NO COM
NC
NO COM
2.2 K
2.2 K
Red
Black
Red
Black
Single Device
Multiple Device
• A short on this Circuit Type equals Alarm.
• A break or a ground in the wiring equals a Tamper.
• Do not reverse the home run's common connection
at the contact, as this will also result in a Tamper
condition.
NC
NOCOM
312
Black
CABLE
1
I
n
p
u
t
I
n
p
u
t
2
C
O
M
C
NO NO
C
NC
2.2 K
Black
Yellow
Black
Black
Yellow
Yellow
Yellow
Black
Junction
NC
NO COM
NC
NO COM
Red
Yellow
Green
2.2 K
NC
Single Device
Multiple Device
Yellow
Y
e
l
l
o
w
• A short on this Circuit Type equals Alarm.
• A break or a ground in the wiring equals a Tamper.
Form "C" Dual Resistor EOL
2.2 K 2.2 K
NC
NOCOM
312
Yellow
Black
CABLE
1
I
n
p
u
t
I
n
p
u
t
2
C
O
M
Yellow
Black
C
NO
NC
• This Circuit Type has 2 end of line resistors, each one 2.2K ohms.
• When the Alarm Input is normal, the Control is looking at both resistors
(total resistance: 1.1K ohms).
• When the Alarm Input is Open (not secure), the control will see 2.2 K
ohms.
• There can only be 1 device on this alarm loop.
- Monitor ISM/xL 1
- Hardware 1
- Contents 3
- Foreword 4
- Monitor ISM 5
- Main Control Board 6
- Enter ID: 7
- Arming Station Reader 8
- Keypad Command Entries 9
- No Commands (Simple Access) 10
- With Commands 10
- IMPORTANT: 11
- Refer to 11
- Ratings / Requirements 11
- 2 Zone Wiring cont 12
- 8 Zone Wiring and Mounting 14
- Adding an Electronic Siren 15
- 22-0375 rev1.1 16
- Output/Relay Card 17
- Version 1 18
- normally 19
- Testing (Signal Strength) 20
- Version 2 Wireless 21
- NA Module Notes 22
- Interface Board 23
- Receiver 23
- V2 Module Programming 25
- ” screen for editing. The 27
- Fire Module 28
- Features: 29
- Graphic Map Module cont 30
- Smart / Vigil Module 31
- Vigil Module 32
- Programming Inputs/Outputs 33
- Checking Status 34
- Door Controller Modules 36
- Version 2 Door Module 37
- Multi-Door 38
- Controller 38
- First Elevator 41
- Connections 41
- Elevator 42
- Elevator Isolator Board 43
- WATERPIPE 45
- Communication Modules 46
- IP Module V3 47
- Direct Connect to PC 49
- Monitor xL 51
- Main Controller 52
- Feature Expansion Board 53
- CPU Failure 54
- ComsLost #50624ef 55
- Enter code 55
- Input Point Expanders 56
- 8 Transistor 57
- Expansion 57
- Module Power Supply 58
- • AC Mains failure 59
- • Battery loss 59
- Single Device 61
- Multiple Device 61
- Control Panel as follows: 62
- Exit 63
Relacionado con productos y manuales para Panel De Control Interlogix Monitor XL Hardware Guide
Panel De Control Interlogix NX-4 Manual de usuario
(44 paginas)
(44 paginas)
Panel De Control Interlogix NX-4 Manual de usuario
(18 paginas)
(18 paginas)
Panel De Control Interlogix NX-6 Manual de usuario
(18 paginas)
(18 paginas)
Panel De Control Interlogix NX-8 Manual de usuario
(61 paginas)
(61 paginas)
Panel De Control Interlogix NX-8 Manual de usuario
(18 paginas)
(18 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales