Interlogix Monitor XL Hardware Guide Manual de usuario descargar pdf (Pagina 46)

42 Monitor ISM/xL™ Hardware Guide

22-0375 rev1.1

Communication Modules

Printer

Printer Serial Port Male DB25 Connector

(viewed from the connections side)

Pin 3 - WHITE

Pin 20 - RED

Pin 5 - BROWN

Pin 7 - BLACK

1432

56

1432

5

1432

5

Tamper Pins

F1

1/2 AMP

P/N 342-3356

Bus communications

indicator



0V

CTS

RTS

RX

TX

Not Used

Printer

TB4

TB2

Printer Module

1432

Module Bus

Data A

Data B

(+) 12V

0V

red

green

yellow

black



Current rating = 61mA

5 digit serial number

to program in Module

Programming

XXXXX

Not Used

TB3

PIN 1 - 13

PIN 14 - 25



Printer Programming

(using LCD Keypad only)

NOTE: The term “HSC” is used to access

the printer abilities in this application.

HSC is a proprietary communications of CSG

Security Inc. and not used in all markets.

• This module has no inputs or outputs.

• Enter the module’s 5-digit address in

Module programming.

• Enable the tamper and make

input/output values “0”. Leave

defaulted to area 1 and leave all other

selections defaulted.

• Press Save. Exit module programming

and then go back to module

programming and the same address.

This initializes the module.

• Check Prn? (Printer) enabled: .

Screen changes to “HSC/Printer

Module Rebooting”. Press OK. Return

to Printer programming screen.

• Enter baud rate for printer:

0 = 1200, 1 = 2400, 2 = 4800,

3 = 9600, 4 = 19200.

• If CTS is enabled (), only users with

authority to view History can start the

printer if it runs out of paper, etc. If it is

disabled (), simply fixing the printer

problem (e.g. load paper) will re-start

the printer. Press Save.

Printer Specifications

Type: RS232 serial 80 columns (or more)

Data Setup: 1 start bit, 1 stop bit, 8 data

bits, no parity, baud rate selectable

(recommend 1200), hardware

handshake.

Printer Connection: female DB25.

Settings for Epson LX300

(P/N 400-0810)

Character spacing = 10cpi, Shape of zero

= 0, Skip-over-perforation = Off,

Character table = PC 437, Auto line feed

= Off, Page length = 11 inches, Auto tear

off = Off, Tractor = Single, Interface =

Serial, Bit rate = 1200 bps (baud), Parity

= None, Data length = 8 bit, EXT/ACK =

On, Software = ESC/P, Auto CR = Off.

To start the Printer

• Enter the History menu in the main

menus and select “Category” and

“App” for application module.

• Select “HSC”.

• Select Printer or Lang for the

language the printer will print in.

• When selecting printer press Start to

start the printer.

• Press Pause to stop printing or

Resume to commence printing.

• Press Cncl to cancel a backlog of

pending messages.

• Press Plog to reprint the entire log in

the History menu.

Wiring Printer Connection to a PC

Serial Port (TB 4: Printer Port)

(when the customer wants the history to

go directly to a computer instead of a

printer)

•

In the module settings, turn off the

CTS option in the Printer Menu.

In the terminal program (‘Terminal.exe’

in Windows for Workgroups; ‘Hyper

Terminal’ in Windows ’95/98) set the

baud rate for the same speed as the

module (typically 1200) and turn off

hardware flow control.

• Only 2 connections are required:

• Connect Tx on the module to Rx on

the PC serial port 9pin 3 on DB25;

pin 2 on DB9).

• Connect OV/Gnd on the module to

0V/Gnd for the serial port (pin 7 on

DB25; pin 5 on DB9).

Refer to Installation Instructions P/N 22-0370 for further information.

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 65 66

Comentarios a estos manuales

Sin comentarios