Interlogix NX-8V2 REV B Installation Manual Manual de usuario descargar pdf

NX-8V2 Control Panel Installation Instructions

Introduction

This is the NX-8V2-Control Panel Installation Instructions.

Installations should only be done by trained professionals. Use

this document to install the system with default settings that

comply with UL requirements.

To install the keypad, other peripherals, and sensors, refer to

the documentation for those devices.

P/N 466-2339 • REV B • 02MAR11

Installation

There are four slots for board insertions inside the metal

enclosure, two on the top and two on the bottom. These allow

the PC board to be positioned vertically (Figure 1 below).

hen you slide the board between the grooves of the slots,

make sure the terminal strip is toward the front opening

(toward you) to allow for the wire connections.

Note: Install the metal enclosure with the door opening from

the top to bottom.

Figure 1: Board installation

NetworX keypad maximum wire run

Table 1 below lists wire lengths for one keypad at the end of

the wire. When connecting more than one keypad to the end of

the wire, a higher gauge wire is required

Table 1: Maximum keypad wire run

Length in feet Wire gauge for NX-

8V2

Wire gauge for NX320-

250 24 22

500 20 18

1000 18 16

1500 16 14

2500 14 12

Terminal descriptions

Table 2 below describes the panel terminals.

Table 2: NX-8V2 terminals

Terminal Description

R1 House telephone ring (grey)..

R Telephone ring (red).

T Telephone tip (green).

T1 House telephone tip (brown).

AC AC input. Connect to a 16.5 V 40 or 50 VA Class ll UL

approved transformer.

EARTH Earth ground. Connect to a cold water pipe or a 6 to 10 ft.

driven rod.

Bell + and

Bell -

If used as a siren output (default), the speaker rating

should be 15 watt at 8 or 16 ohm, or 30/40 watt at 4, 8, or

16 ohms. If voltage ouput is selected in location 37, this

output becomes voltage output, 12 VDC, 1 Amp maximum

load. Note: A 3.3 kohm resistor may be required across

the bell terminals when a 12 VDC siren is used. If no

resistor is used, you may experience voltage leakage into

the siren, which will cause these devices to output a small

signal.

KP Data Connect to the data terminal on the keypads and the

expanders. Maximum number of devices (keypads plus

expanders) is 32. See Maximum Wire Run table.

KP COM Connect to the common terminal on the keypads and the

expanders.

1 2 3 4 5 6 ... 10 11

Indice de contenidos

Pagina 1 - Installation

NX-8V2 Control Panel Installation Instructions Introduction This is the NX-8V2-Control Panel Installation Instructions. Installations should only be

Pagina 2 - Control panel programming

ANSI/SIA CP-01 requirements CP-01 feature descriptions and specifications are listed in Table 9 below. The following are requirements for compliance w

Pagina 3

NX-8V2 Control Panel Installation Instructions 11 CP-O1 feature description Feature description as shown in manual Program location Seg/opt Default

Pagina 4 - Location 0 - Phone 1

Terminal Description KP POS Connect to the POS terminal on the keypads and the expanders. Individually, this terminal is limited to 1 amp. Combined,

Pagina 5 - Zone type Description

Select the module to program Since all modules connected to the NX-8V2 are programmed through the keypad, the module you are programming should be the

Pagina 6

Location 0 - Phone 1 Location 0 has 20 segments of numerical data. Use this location to program phone 1. The default for each segment is 14. • To pro

Pagina 7

Segment 2 - Phone 1 backup control Program the backup control for phone 1. The default is 0. • Program a 0 in segment 2 to cause the NX-8V2 to make t

Pagina 8

Zone type Description Zone type Description 2. 24-hour audible. This zone creates an instant yelping siren alarm regardless of the armed state of th

Pagina 9 - Regulatory information

UL294 Access control system units UL365 Police station connected burglar alarms UL609, CAN/ULC-S303-M91 Mercantile, police station connect with basic

Pagina 10 - ANSI/SIA CP-01 requirements

protected area, is acceptable, provided it is rated for outside service and alarm conditions are transmitted to: a) The dispatch location of the law e

Pagina 11

NX-8V2 Control Panel Installation Instructions 9 • The DACT shall be enabled for all commercial burglary applications. UL requires that an alarm pan

Comentarios a estos manuales

Sin comentarios

Interlogix NX-8V2 REV B Installation Manual Manual de usuario

Busca en linea o descarga Manual de usuario para Panel De Control Interlogix NX-8V2 REV B Installation Manual. Interlogix NX-8V2 REV B Installation Manual User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Panel De Control Interlogix NX-8V2 REV B Installation Manual