Interlogix Concord 4 REV J Installation Manual Manual de usuario Pagina 57
- Pagina / 153
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3: Programming
Concord 4 Installation Manual 51
Phones - central station phone 1 to 3 settings
Phone number
Shortcut: 01000,
01010, and 01020
Default: None
Use this setting to program the central station receiver phone number.
Phone numbers can be 1 to 24 digits long, including pauses or *and #
characters.
The phone menus are not accessible if a dealer code is programmed
and the installer code is used to enter installer programming mode. To
access these menus when a dealer code is programmed, you must
enter installer programming mode using the dealer code. Call-waiting
services should be disabled to prevent interrupting panel communication
to the central monitoring station. To program a dialing prefix that
disables call waiting, see the call wait cancel setting under the menu
“Phone options - global settings” on page 54.
To delete a central station phone number, with the display showing
PHONE NUMBER (current number), press D. The display shows
PHONE NUMBER _.
High level reports
Shortcut: 01001,
01011, and 01021
Default: On (1),
Off (2 and 3)
When this setting is on, the following conditions report to the central
station:
• Fire, police, auxiliary, and duress alarms
• No activity
• Receiver failure (or jam)
• Tamper conditions, including zone tampers and system tamper (40
incorrect key presses or touchpad supervisory)
• Entering or exiting sensor test mode
• Phone test
Low level reports
Shortcut: 01002,
01012, and 01022
Default: On (1),
Off (2 and 3)
When this setting is on, the following nonalarm conditions report to the
central station:
• Force armed
• Hardwired zone trouble (open or short)
• Supervisory (wireless devices)
• Low battery (wireless devices)
• Phone test
• Other nonalarm related conditions
Exception reports
Shortcut: 01003,
01013, and 01023
Default: Off
When this setting is on, the panel reports to the central station if the
system is not armed or disarmed at the specified schedule times.
Open/close reports
Shortcut: 01004,
01014, and 01024
Default: Off
This setting determines whether opening and closing reports are sent to
the central station. When turned on, the panel sends a closing report
when the system is armed and an opening report when the system is
disarmed.
To use this feature, the opening reports and closing reports settings
under the “Reporting menu” on page 61 must be turned on for that
partition.
- P/N 466-2182 • REV J • NOV12 1
- Content 3
- Important information 5
- Chapter 1 7
- Introduction 7
- Planning the installation 8
- SuperBus 2000 bus devices 9
- Chapter 1: Introduction 10
- Chapter 2 11
- Installation 11
- Installation overview 12
- Chapter 2: Installation 13
- Chapter 2: Installation 14
- Mounting the panel 16
- Grounding the panel 17
- Antenna shrouds 18
- Optional SnapCards 19
- Panel terminals 20
- Intrusion detection devices 21
- Smoke detectors 21
- Four-wire smoke detectors 23
- Speakers and sirens 24
- SPKR SPKR SPKR SPKR 25
- Not used 25
- To zone input 26
- SuperBus 2000 touchpads 28
- SuperBus 2000 modules 28
- Power supply terminals 29
- To power inputs on devices 29
- GND +12V A BUS B 29
- Hardwired interior 32
- RJ31X phone jack 34
- AC power transformer 36
- Backup battery 37
- Power up 37
- Chapter 3 39
- Programming 39
- Overview 40
- Programming touchpad 41
- Quick programming mode 42
- Tier 1 programming menus 43
- DEMO KIT MODE OFF/ON (new 44
- Chapter 3: Programming 45
- Tier 2 programming menus 46
- Shortcut numbers 50
- Security menu 51
- KEYCHAIN TP PTN), then 54
- PARTITION 54
- Phones menu 56
- PHONE NUMBER _ 57
- NUMBER _ 58
- Phone options menu 60
- Timers menu 63
- SLEEP TIME 64
- NO USAGE 64
- Light control menu 65
- Touchpad options menu 66
- Reporting menu 67
- Siren options menu 72
- Sensors menu 73
- S01 P1 G13 NC HW BACK DOOR 75
- EDIT SENSORS 75
- SENSOR GROUP nn 75
- Audio verification menu 77
- AUDIO VERIFY 78
- Accessory modules menu 79
- DEVICE ID (current ID) 80
- DEVICE PTN and then press 80
- PARTITION ASSIGN n 80
- OUTPUTS 81
- OUTPUT 1 81
- PARTITION ASSIGN 1 81
- CONFIGURATION tttrr 81
- Onboard options menu 84
- Macro keys menu 87
- User programming mode 88
- Time and date menu 89
- User codes menu 90
- Options menu 93
- Set up schedules menu 94
- Energy saver menu 98
- Downloader programming 99
- Chapter 3: Programming 100
- Chapter 4 101
- Testing and 101
- Testing the system 102
- Zones/sensors 103
- Phone communication 104
- Outputs and sirens 106
- Light control 107
- Energy saver module (ESM) 107
- Touchpad display contrast 108
- Troubleshooting 112
- Access code issues 114
- Arming and disarming issues 114
- Bypassing issues 115
- Alphanumeric touchpad issues 116
- Speaker issues 117
- Siren issues 117
- Hardwired zone issues 118
- Wireless sensor zone issues 118
- Wireless touchpad issues 119
- Phone issues 119
- Light control issues 120
- Energy saver module issues 120
- Automation module issues 121
- Appendix A 123
- System planning sheets 123
- Customer information 124
- Wireless devices 124
- Hardware devices 125
- Zone and sensor assignments 127
- Appendix B 135
- Reference tables 135
- Sensor group characteristics 136
- Appendix B: Reference tables 138
- Cross-zoning 139
- Sensor text 140
- System event triggers 142
- Sensor group event triggers 143
- Sensor number event triggers 144
- Response characteristics 149
- Response numbers 149
- Specifications 151
Relacionado con productos y manuales para Panel De Control Interlogix Concord 4 REV J Installation Manual
Panel De Control Interlogix NX-4 Manual de usuario
(44 paginas)
(44 paginas)
Panel De Control Interlogix NX-4 Manual de usuario
(18 paginas)
(18 paginas)
Panel De Control Interlogix NX-6 Manual de usuario
(18 paginas)
(18 paginas)
Panel De Control Interlogix NX-8 Manual de usuario
(61 paginas)
(61 paginas)
Panel De Control Interlogix NX-8 Manual de usuario
(18 paginas)
(18 paginas)
Canon Dispositivi multifunzione manuali utente
Partendo da P
Comentarios a estos manuales