Interlogix Concord 4 REV J Installation Manual Manual de usuario Pagina 147
- Pagina / 153
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix B: Reference tables
Concord 4 Installation Manual 141
Sensor number
State
Trigger
number
State
Trigger number
Sensor 95
In alarm
223
Open
351
Sensor 96
In alarm
224
Open
352
System feature event triggers
Table 29 below describes the system feature event triggers.
Table 29: System feature event trigger numbers
Feature
State
Trigger number
Phone test
Initiated
225
AC failure
For 15 minutes
226
CPU low battery
Detected (excluding first minute after power-
up)
227
Auto phone test
Begun
228
Receiver failure
Detected
229
Back in service
Alarm (AC loss, battery drain, then AC
restore)
230
Phone failure
Detected
231
Buffer full
Detected
232
Two trip error
Detected
233
System tamper
Alarm (40 incorrect code entry keystrokes)
237
Freeze
Alarm
238
No activity
Alarm
239
Fire panic
Alarm
240
Police panic
Alarm
241
Auxiliary panic
Alarm
242
Opening report
Occurred
243
Closing report
Occurred
244
Latchkey opening or
closing
Occurred
245
Duress
Alarm
246
Forced armed report
Occurred
247
Fire in partition
Alarm
248
- P/N 466-2182 • REV J • NOV12 1
- Content 3
- Important information 5
- Chapter 1 7
- Introduction 7
- Planning the installation 8
- SuperBus 2000 bus devices 9
- Chapter 1: Introduction 10
- Chapter 2 11
- Installation 11
- Installation overview 12
- Chapter 2: Installation 13
- Chapter 2: Installation 14
- Mounting the panel 16
- Grounding the panel 17
- Antenna shrouds 18
- Optional SnapCards 19
- Panel terminals 20
- Intrusion detection devices 21
- Smoke detectors 21
- Four-wire smoke detectors 23
- Speakers and sirens 24
- SPKR SPKR SPKR SPKR 25
- Not used 25
- To zone input 26
- SuperBus 2000 touchpads 28
- SuperBus 2000 modules 28
- Power supply terminals 29
- To power inputs on devices 29
- GND +12V A BUS B 29
- Hardwired interior 32
- RJ31X phone jack 34
- AC power transformer 36
- Backup battery 37
- Power up 37
- Chapter 3 39
- Programming 39
- Overview 40
- Programming touchpad 41
- Quick programming mode 42
- Tier 1 programming menus 43
- DEMO KIT MODE OFF/ON (new 44
- Chapter 3: Programming 45
- Tier 2 programming menus 46
- Shortcut numbers 50
- Security menu 51
- KEYCHAIN TP PTN), then 54
- PARTITION 54
- Phones menu 56
- PHONE NUMBER _ 57
- NUMBER _ 58
- Phone options menu 60
- Timers menu 63
- SLEEP TIME 64
- NO USAGE 64
- Light control menu 65
- Touchpad options menu 66
- Reporting menu 67
- Siren options menu 72
- Sensors menu 73
- S01 P1 G13 NC HW BACK DOOR 75
- EDIT SENSORS 75
- SENSOR GROUP nn 75
- Audio verification menu 77
- AUDIO VERIFY 78
- Accessory modules menu 79
- DEVICE ID (current ID) 80
- DEVICE PTN and then press 80
- PARTITION ASSIGN n 80
- OUTPUTS 81
- OUTPUT 1 81
- PARTITION ASSIGN 1 81
- CONFIGURATION tttrr 81
- Onboard options menu 84
- Macro keys menu 87
- User programming mode 88
- Time and date menu 89
- User codes menu 90
- Options menu 93
- Set up schedules menu 94
- Energy saver menu 98
- Downloader programming 99
- Chapter 3: Programming 100
- Chapter 4 101
- Testing and 101
- Testing the system 102
- Zones/sensors 103
- Phone communication 104
- Outputs and sirens 106
- Light control 107
- Energy saver module (ESM) 107
- Touchpad display contrast 108
- Troubleshooting 112
- Access code issues 114
- Arming and disarming issues 114
- Bypassing issues 115
- Alphanumeric touchpad issues 116
- Speaker issues 117
- Siren issues 117
- Hardwired zone issues 118
- Wireless sensor zone issues 118
- Wireless touchpad issues 119
- Phone issues 119
- Light control issues 120
- Energy saver module issues 120
- Automation module issues 121
- Appendix A 123
- System planning sheets 123
- Customer information 124
- Wireless devices 124
- Hardware devices 125
- Zone and sensor assignments 127
- Appendix B 135
- Reference tables 135
- Sensor group characteristics 136
- Appendix B: Reference tables 138
- Cross-zoning 139
- Sensor text 140
- System event triggers 142
- Sensor group event triggers 143
- Sensor number event triggers 144
- Response characteristics 149
- Response numbers 149
- Specifications 151
Relacionado con productos y manuales para Panel De Control Interlogix Concord 4 REV J Installation Manual
Panel De Control Interlogix NX-4 Manual de usuario
(44 paginas)
(44 paginas)
Panel De Control Interlogix NX-4 Manual de usuario
(18 paginas)
(18 paginas)
Panel De Control Interlogix NX-6 Manual de usuario
(18 paginas)
(18 paginas)
Panel De Control Interlogix NX-8 Manual de usuario
(61 paginas)
(61 paginas)
Panel De Control Interlogix NX-8 Manual de usuario
(18 paginas)
(18 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales