Interlogix NS3550-2T-8S User Manual Manual de usuario Pagina 286
- Pagina / 631
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IFS NS3552-8P-2S AND NS3550-2T-8S User Manual
286
4.13 MAC Address Table
Switching of frames is based upon the DMAC address contained in the frame. The Managed Switch builds up a table that maps
MAC addresses to switch ports for knowing which ports the frames should go to (based upon the DMAC address in the frame).
This table contains both static and dynamic entries. The static entries are configured by the network administrator if the
administrator wants to do a fixed mapping between the DMAC address and switch ports.
The frames also contain a MAC address (SMAC address), which shows the MAC address of the equipment sending the frame.
The SMAC address is used by the switch to automatically update the MAC table with these dynamic MAC addresses. Dynamic
entries are removed from the MAC table if no frame with the corresponding SMAC address has been seen after a configurable
age time.
4.13.1 MAC Address Table Configuration
The MAC Address Table is configured on this page. Set timeouts for entries in the dynamic MAC Table and configure the static
MAC table here. The MAC Address Table Configuration screen in Figure 4-13-1 appears.
Figure 4-13-1: MAC Address Table Configuration Page Screenshot
- IFS NS3552-8P-2S and 1
- -2T-8S User Manual 1
- TABLE OF CONTENTS 3
- 1. INTRODUCTION 24
- 1.2 Product Description 25
- 1.3 How to Use This Manual 29
- 1.4 Product Features 30
- 1.5 Product Specifications 34
- 2. INSTALLATION 38
- 2.1.2 Front Panel 39
- 2.1.3 LED Indicators 41
- 2.1.4 Wiring the Power Input 42
- 2.2.1 Installation Steps 46
- 2.2.2 DIN-Rail Mounting 47
- 2.3 Cabling 50
- 2.3.2 Remove the Module 53
- 3. SWITCH MANAGEMENT 54
- 3.3 CLI Mode Management 56
- 3.4 Web Management 58
- 4. WEB CONFIGURATION 60
- 4.1 Main Web Page 63
- 4.2 System 65
- 4.2.2 IP Configuration 66
- 4.2.3 IPv6 Configuration 68
- 4.2.4 Users Configuration 69
- 4.2.5 Privilege Levels 71
- 4.2.6 NTP Configuration 73
- 4.2.7 Daylight Saving 74
- 4.2.8 UPnP 76
- 4.2.9 DHCP Relay 78
- 4.2.10 DHCP Relay Statistics 79
- 4.2.11 CPU Load 80
- 4.2.12 System Log 81
- 4.2.13 Detailed Log 83
- 4.2.14 Remote Syslog 83
- 4.2.15 SMTP Configuration 85
- 4.2.16 Digital Input/output 86
- 4.2.17 Fault Alarm 88
- 4.2.18 EEE Power Reduction 89
- 4.2.19 Web Firmware Upgrade 90
- 4.2.20 TFTP Firmware Upgrade 91
- 4.2.21 Configuration Backup 92
- 4.2.22 Configuration Upload 93
- 4.2.23 Image Select 95
- 4.2.24 Factory Default 96
- 4.2.25 System Reboot 97
- 4.3.1 SNMP Overview 98
- 4.3.4 SNMPv3 Configuration 102
- 4.4 Port Management 107
- 4.4.3 Port Statistics Detail 110
- 4.4.4 SFP Information 111
- 1000Base-SX 112
- 1000Base-LX 112
- 100Base-FX 112
- 4.4.5 Port Mirror 113
- • Mirror Port Configuration 114
- 4.5 Link Aggregation 115
- 4.5.1 Static Aggregation 118
- 4.5.2 LACP Configuration 120
- 4.5.3 LACP System Status 121
- 4.5.4 LACP Port Status 122
- 4.5.5 LACP Port Statistics 122
- 4.6 VLAN 124
- ■ Port VLAN ID 126
- 4.6.3 VLAN Basic Information 128
- 4.6.5 VLAN Membership 133
- 4.6.6 VLAN Membership Status 134
- 4.6.7 VLAN Port Status 136
- 4.6.8 Private VLAN 137
- 4.6.9 Port Isolation 138
- 4.6.10 VLAN Setting Example: 139
- 4.6.10.3 Port Isolate 145
- 4.6.11 MAC-based VLAN 146
- 4.6.12 MAC-based VLAN Status 147
- 4.6.13 Protocol-based VLAN 148
- 4.7 Spanning Tree Protocol 151
- 4.7.3 Bridge Status 159
- 4.7.5 MSTI Priorities 163
- 4.7.6 MSTI Configuration 164
- 4.7.8 Port Status 167
- 4.7.9 Port Statistics 168
- 4.8 Multicast 170
- Type Response Time 172
- 4.8.5 IGMP Snooping Status 179
- 4.8.6 IGMP Group Information 180
- 4.8.7 IGMPv3 Information 181
- 4.8.11 MLD Snooping Status 186
- 4.8.13 MLDv2 Information 188
- 4.8.14 MVR 189
- 4.8.15 MVR Status 191
- 4.8.17 MVR SFM Information 192
- 4.9 Quality of Service 194
- 4.9.2 Port Policing 195
- 4.9.3 Port Shaping 195
- 4.9.4 Port Classification 198
- 4.9.5 Port Scheduler 200
- 4.9.6 Port Tag Remarking 201
- 4.9.7 Port DSCP 202
- 4.9.8 DSCP-Based QoS 204
- 4.9.9 DSCP Translation 205
- 4.9.10 DSCP Classification 207
- 4.9.11 QoS Control List 208
- 4.9.12 QoS Status 210
- 4.9.13 Queue Policing 211
- 4.9.15 QoS Statistics 213
- 4.10 Access Control Lists 217
- 4.10.3 ACE Configuration 222
- 4.11 Authentication 232
- Port Configuration 240
- Port State 245
- Port Counters 246
- 4.11.7 RADIUS Overview 253
- 4.11.8 RADIUS Details 256
- RADIUS Accounting Servers 258
- 4.12 Security 268
- System Configuration 269
- 4.12.2 Access Management 272
- 4.12.4 HTTPs 274
- 4.12.5 SSH 275
- 4.12.6 Port Security Status 275
- 4.12.7 Port Security Detail 278
- 4.12.8 DHCP Snooping 278
- 4.12.12 ARP Inspection 284
- 4.13 MAC Address Table 286
- 4.14 LLDP 292
- Port Policies Configuration 299
- 4.14.4 LLDP-MED Neighbor 301
- 4.14.5 Neighbor 304
- 4.14.6 Port Statistics 304
- Global Counters 305
- Local Counters 306
- 4.15 Diagnostics 307
- 4.15.1 Ping 308
- 4.15.2 IPv6 Ping 309
- 4.15.3 Remote IP Ping Test 309
- 4.15.4 Cable Diagnostics 311
- 4.16 Power over Ethernet 312
- 4.16.2 System Configuration 314
- 4.16.3 Port Configuration 317
- 4.16.4 PoE Status 318
- 4.16.5 PoE Schedule 320
- 4.16.6 LLDP PoE Neighbors 323
- 4.17 Loop Protection 326
- 4.17.2 Status 327
- Buttons 328
- 4.18 RMON 329
- 4.18.2 RMON Alarm Status 331
- 4.18.4 RMON Event Status 333
- 4.18.6 RMON History Status 334
- 4.19 Ring 338
- 4.19.1 MEP Configuration 340
- Instance Data: 341
- 4.19.5 Ring Wizard 347
- 4.19.6 Ring Wizard Example: 349
- 5. COMMAND LINE INTERFACE 352
- 6. COMMAND LINE MODE 353
- 6.1 System Command 354
- 6.2 IP Command 363
- 6.3 Port Management Command 372
- 6.7 Security Command 396
- 6.9 Link Aggregation Command 477
- Example: 479
- LACP Timeout 484
- 6.11 LLDP Command 485
- 6.12 LLDP MED Command 490
- LLDP MED ECS 491
- behavior for the specified 493
- LLDP MED Info 495
- 6.13 EEE Command 496
- 6.14 Thermal Command 498
- Thermal Configuration 499
- PoE Status 502
- EVC ECE Add 507
- EVC ECE Status 509
- MEP Config 512
- QoS QCL Add 539
- 6.20 Mirror Command 543
- 6.21 Configuration Command 545
- 6.22 Firmware Command 546
- Firmware Swap 547
- 6.23 UPnP Command 548
- 6.24 MVR Command 550
- MVR VLAN LLQI 552
- 6.25 Voice VLAN Command 556
- ERPS Command 562
- ERPS RPL Owner 566
- 6.27 Loop Protect Command 570
- 6.28 IPMC Command 573
- 6.30 SMTP Command 591
- 6.31 DIDO Command 595
- 6.32 Show Command 600
- Show STP 607
- 7. SWITCH OPERATION 608
- 7.5 Auto-Negotiation 609
- 8. TROUBLE SHOOTING 610
- APPENDEX A 612
- APPENDEX B: GLOSSARY 614
- Aggregation 615
Relacionado con productos y manuales para Accesorios de comunicación Interlogix NS3550-2T-8S User Manual
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales