Interlogix NS3550-2T-8S User Manual Manual de usuario Pagina 219
- Pagina / 631
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
IFS NS3552-8P-2S AND NS3550-2T-8S User Manual
219
• Rate Limiter
Indicates the rate limiter number of the ACE. The allowed range is 1 to 16. When
Disabled is displayed, the rate limiter operation is disabled.
• Port Redirect
Indicates the port redirect operation of the ACE. Frames matching the ACE are
redirected to the port number.
The allowed values are Disabled or a specific port number. When Disabled is
displayed, the port redirect operation is disabled.
• Mirror
Specify the mirror operation of this port. The allowed values are:
Enabled: Frames received on the port are mirrored.
Disabled: Frames received on the port are not mirrored.
The default value is "Disabled".
• CPU
Forward packet that matched the specific ACE to CPU.
• CPU Once
Forward first packet that matched the specific ACE to CPU.
• Counter
The counter indicates the number of times the ACE was hit by a frame.
• Conflict
Indicates the hardware status of the specific ACE. The specific ACE is not applied
to the hardware due to hardware limitations.
Buttons
: Select the ACL status from this drop down list.
Auto-refresh
: Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds.
: Click to refresh the page immediately.
- IFS NS3552-8P-2S and 1
- -2T-8S User Manual 1
- TABLE OF CONTENTS 3
- 1. INTRODUCTION 24
- 1.2 Product Description 25
- 1.3 How to Use This Manual 29
- 1.4 Product Features 30
- 1.5 Product Specifications 34
- 2. INSTALLATION 38
- 2.1.2 Front Panel 39
- 2.1.3 LED Indicators 41
- 2.1.4 Wiring the Power Input 42
- 2.2.1 Installation Steps 46
- 2.2.2 DIN-Rail Mounting 47
- 2.3 Cabling 50
- 2.3.2 Remove the Module 53
- 3. SWITCH MANAGEMENT 54
- 3.3 CLI Mode Management 56
- 3.4 Web Management 58
- 4. WEB CONFIGURATION 60
- 4.1 Main Web Page 63
- 4.2 System 65
- 4.2.2 IP Configuration 66
- 4.2.3 IPv6 Configuration 68
- 4.2.4 Users Configuration 69
- 4.2.5 Privilege Levels 71
- 4.2.6 NTP Configuration 73
- 4.2.7 Daylight Saving 74
- 4.2.8 UPnP 76
- 4.2.9 DHCP Relay 78
- 4.2.10 DHCP Relay Statistics 79
- 4.2.11 CPU Load 80
- 4.2.12 System Log 81
- 4.2.13 Detailed Log 83
- 4.2.14 Remote Syslog 83
- 4.2.15 SMTP Configuration 85
- 4.2.16 Digital Input/output 86
- 4.2.17 Fault Alarm 88
- 4.2.18 EEE Power Reduction 89
- 4.2.19 Web Firmware Upgrade 90
- 4.2.20 TFTP Firmware Upgrade 91
- 4.2.21 Configuration Backup 92
- 4.2.22 Configuration Upload 93
- 4.2.23 Image Select 95
- 4.2.24 Factory Default 96
- 4.2.25 System Reboot 97
- 4.3.1 SNMP Overview 98
- 4.3.4 SNMPv3 Configuration 102
- 4.4 Port Management 107
- 4.4.3 Port Statistics Detail 110
- 4.4.4 SFP Information 111
- 1000Base-SX 112
- 1000Base-LX 112
- 100Base-FX 112
- 4.4.5 Port Mirror 113
- • Mirror Port Configuration 114
- 4.5 Link Aggregation 115
- 4.5.1 Static Aggregation 118
- 4.5.2 LACP Configuration 120
- 4.5.3 LACP System Status 121
- 4.5.4 LACP Port Status 122
- 4.5.5 LACP Port Statistics 122
- 4.6 VLAN 124
- ■ Port VLAN ID 126
- 4.6.3 VLAN Basic Information 128
- 4.6.5 VLAN Membership 133
- 4.6.6 VLAN Membership Status 134
- 4.6.7 VLAN Port Status 136
- 4.6.8 Private VLAN 137
- 4.6.9 Port Isolation 138
- 4.6.10 VLAN Setting Example: 139
- 4.6.10.3 Port Isolate 145
- 4.6.11 MAC-based VLAN 146
- 4.6.12 MAC-based VLAN Status 147
- 4.6.13 Protocol-based VLAN 148
- 4.7 Spanning Tree Protocol 151
- 4.7.3 Bridge Status 159
- 4.7.5 MSTI Priorities 163
- 4.7.6 MSTI Configuration 164
- 4.7.8 Port Status 167
- 4.7.9 Port Statistics 168
- 4.8 Multicast 170
- Type Response Time 172
- 4.8.5 IGMP Snooping Status 179
- 4.8.6 IGMP Group Information 180
- 4.8.7 IGMPv3 Information 181
- 4.8.11 MLD Snooping Status 186
- 4.8.13 MLDv2 Information 188
- 4.8.14 MVR 189
- 4.8.15 MVR Status 191
- 4.8.17 MVR SFM Information 192
- 4.9 Quality of Service 194
- 4.9.2 Port Policing 195
- 4.9.3 Port Shaping 195
- 4.9.4 Port Classification 198
- 4.9.5 Port Scheduler 200
- 4.9.6 Port Tag Remarking 201
- 4.9.7 Port DSCP 202
- 4.9.8 DSCP-Based QoS 204
- 4.9.9 DSCP Translation 205
- 4.9.10 DSCP Classification 207
- 4.9.11 QoS Control List 208
- 4.9.12 QoS Status 210
- 4.9.13 Queue Policing 211
- 4.9.15 QoS Statistics 213
- 4.10 Access Control Lists 217
- 4.10.3 ACE Configuration 222
- 4.11 Authentication 232
- Port Configuration 240
- Port State 245
- Port Counters 246
- 4.11.7 RADIUS Overview 253
- 4.11.8 RADIUS Details 256
- RADIUS Accounting Servers 258
- 4.12 Security 268
- System Configuration 269
- 4.12.2 Access Management 272
- 4.12.4 HTTPs 274
- 4.12.5 SSH 275
- 4.12.6 Port Security Status 275
- 4.12.7 Port Security Detail 278
- 4.12.8 DHCP Snooping 278
- 4.12.12 ARP Inspection 284
- 4.13 MAC Address Table 286
- 4.14 LLDP 292
- Port Policies Configuration 299
- 4.14.4 LLDP-MED Neighbor 301
- 4.14.5 Neighbor 304
- 4.14.6 Port Statistics 304
- Global Counters 305
- Local Counters 306
- 4.15 Diagnostics 307
- 4.15.1 Ping 308
- 4.15.2 IPv6 Ping 309
- 4.15.3 Remote IP Ping Test 309
- 4.15.4 Cable Diagnostics 311
- 4.16 Power over Ethernet 312
- 4.16.2 System Configuration 314
- 4.16.3 Port Configuration 317
- 4.16.4 PoE Status 318
- 4.16.5 PoE Schedule 320
- 4.16.6 LLDP PoE Neighbors 323
- 4.17 Loop Protection 326
- 4.17.2 Status 327
- Buttons 328
- 4.18 RMON 329
- 4.18.2 RMON Alarm Status 331
- 4.18.4 RMON Event Status 333
- 4.18.6 RMON History Status 334
- 4.19 Ring 338
- 4.19.1 MEP Configuration 340
- Instance Data: 341
- 4.19.5 Ring Wizard 347
- 4.19.6 Ring Wizard Example: 349
- 5. COMMAND LINE INTERFACE 352
- 6. COMMAND LINE MODE 353
- 6.1 System Command 354
- 6.2 IP Command 363
- 6.3 Port Management Command 372
- 6.7 Security Command 396
- 6.9 Link Aggregation Command 477
- Example: 479
- LACP Timeout 484
- 6.11 LLDP Command 485
- 6.12 LLDP MED Command 490
- LLDP MED ECS 491
- behavior for the specified 493
- LLDP MED Info 495
- 6.13 EEE Command 496
- 6.14 Thermal Command 498
- Thermal Configuration 499
- PoE Status 502
- EVC ECE Add 507
- EVC ECE Status 509
- MEP Config 512
- QoS QCL Add 539
- 6.20 Mirror Command 543
- 6.21 Configuration Command 545
- 6.22 Firmware Command 546
- Firmware Swap 547
- 6.23 UPnP Command 548
- 6.24 MVR Command 550
- MVR VLAN LLQI 552
- 6.25 Voice VLAN Command 556
- ERPS Command 562
- ERPS RPL Owner 566
- 6.27 Loop Protect Command 570
- 6.28 IPMC Command 573
- 6.30 SMTP Command 591
- 6.31 DIDO Command 595
- 6.32 Show Command 600
- Show STP 607
- 7. SWITCH OPERATION 608
- 7.5 Auto-Negotiation 609
- 8. TROUBLE SHOOTING 610
- APPENDEX A 612
- APPENDEX B: GLOSSARY 614
- Aggregation 615
Relacionado con productos y manuales para Accesorios de comunicación Interlogix NS3550-2T-8S User Manual
(14 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales