Interlogix Simon XTi CDMA Module V4 Manual de usuario descargar pdf (Pagina 9)

Simon XT/XTi CDMA Module V4 Installation Instructions 9

other commands.)

---- Replicate Mode

Initiates replicate mode on the panel.

---- Send Node Info

For advanced use only. Do not use

unless directed to do so by Alarm.com.

---- Refresh Thermostat

Requests updated thermostat data.

1 I

All Image Sensor menus are only available when an Image Sensor

daughterboard has been connected to the module. An Image Sensor

daughterboard is required to enable Image Sensor functionality. For use

with Simon XTi only

Refer to the emPower

installation instructions and guides on the

Alarm.com Dealer Site for more information on Z-Wave enrollment and

troubleshooting.

Walking the Customer through New User Setup on the

Web

This section describes how to help your customer set up their

website account, and only applie

s to customers on an interactive

service plan with an online account. (Skip this step if the customer

is using the module for wireless signaling only).

Before the customer can configure their website account, the

Alarm.com account for that customer must be created on the

Dealer Site, and the CDMA module associated with the account

must be installed successfully.

To log in and access their account, the customer can go to

www.alarm.com (or custom dealer website address) to complete

the new subscriber setup procedure.

The customer will need the following:

• The website login and temporary password included on the

Alarm.com Welcome Letter generated when the account

was created by the

Dealer

• A list of their system sensors and touch screens with

corresponding zone IDs

• At least one phone number and e-mail address where

notifications can be sent

Note: At least one sensor must be learned into the panel to

complete the new subscriber setup. If not all sensors and touch

screens were learned in before powering up the module, an

updated sensor list must be requested by performing a CDMA

phone test or requesting an updated equipment list from the

Dealer Site.

Specifications

Compatibility Simon XT panels with software versions 0.0.H

and later and Simon XTi

Power requirements 6V nominal

Peak current 1.7A

Operating temperature 32 to 120°F (0 to 49°C)

Storage temperature -30 to 140°F (-34 to 60°C)

Max. relative humidity 90% non-condensing

Cellular network dual

band

CDMA/1xRTT

Dimensions 4 1/16 x 1 7/8 in. (H x W)

Listings FCC Part 15, Verizon Certified

Regulatory information

Changes or modifications not expressly approved by Alarm.com

can void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful inter

ference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

form that which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for

help.

Operation is subject to the following two conditions:

(1) This device may not cause interference

(2) This device must accept any interference, incl

uding

interference that may cause undesired operation of the device

This equipment complies with the FCC RF radiation exposure limits

set forth for an uncontrolled environment. This equipment should

be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

FCC IDs: YL6-143200C5V4

If equipped with Image Sensor daughterboard, FCC ID: YL6-

143200C5V4IS

This device contains FCC ID: RI7CC864-DUAL, IC: 5131A-CC864-

DUAL

1 2 3 4 5 6 7 8 9

Comentarios a estos manuales

Sin comentarios

Interlogix Simon XTi CDMA Module V4 Manual de usuario Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios de comunicación Interlogix Simon XTi CDMA Module V4