Interlogix NS2503-24P/2C User Manual Manual de usuario Pagina 20
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
NS2503-24P/2C User Manual
20
Rack Mounting
To install the Managed Switch in a 19-inch standard rack, please follows the instructions described below.
Step1: Place the Managed Switch on a flat surface, with the front panel positioned towards the front side.
Step2: Attach the rack-mount bracket to each side of the Managed Switch with the supplied screws included in the package.
Figure 2-5 shows how to attach brackets to one side of the Managed Switch.
Figure 2-5: Attach brackets to the Managed Switch
You must use the screws supplied with the mounting brackets. Damage caused to the parts
by using incorrect screws would invalidate the warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the Managed Switch, use matching screws to securely attach the brackets to the rack,
as shown in Figure 2-6.
Figure 2-6: Mounting the Switch in a Rack
Step6: Proceed with the step 4 and step 5 of section 2.2.1. Desktop Installation to connect the network cabling and supply
power to the Managed Switch.
- IFS NS2503-24P/2C User 1
- TABLE OF CONTENTS 3
- Introduction 8
- How to Use This Manual 10
- Product Features 11
- Product Specification 13
- INSTALLATION 15
- LED Indications 16
- Switch Rear Panel 18
- Install the Switch 19
- Rack Mounting 20
- SWITCH MANAGEMENT 23
- Management Access Overview 24
- Web Management 25
- Administration Console 26
- Protocols 28
- Web-Based Management 29
- Requirements 30
- Main WEB PAGE 32
- System Information 35
- Misc Config 36
- Console Port Info 40
- SNMP Configuration 41
- SNMPv3 Groups 44
- SNMPv3 View 45
- SNMPv3 Access 46
- SNMP V3 usm-user 48
- Syslog Setting 49
- System Log 50
- SNTP Setting 51
- Firmware Upgrade 52
- HTTP Firmware Upgrade 53
- Configuration Backup 54
- TFTP Backup Configuration 55
- Factory Default 56
- System Reboot 56
- Rate Control 59
- Port Status 60
- Port Statistics 61
- Port Sniffer 62
- Protect Port 64
- Remote Ping 65
- VLAN configuration 66
- Port VLAN ID 67
- Default VLANs 67
- Static VLAN Configuration 68
- Port-based VLAN 69
- 802.1Q VLAN 71
- VLAN Group Configuration 72
- VLAN Filter 75
- GVRP VLAN 76
- GVRP Setting 77
- GVRP Table 78
- Q-in-Q VLAN 79
- Q-in-Q Port Setting 80
- Q-in-Q Tunnel Setting 81
- To configure QinQ Port 81
- Trunking 82
- Aggregator setting 83
- Aggregator Information 84
- LACP enabled 85
- Switch 1 configuration 85
- Switch 2 configuration 86
- State Activity 88
- Forwarding and Filtering 89
- Static MAC Table 90
- MAC Filtering 91
- IGMP Snooping 92
- IGMP Configuration 96
- Static Multicast Table 98
- Spanning Tree Protocol 100
- NS2503-24P/2C User Manual 101
- Illustration of STP 103
- STP Parameters 104
- STP System Configuration 105
- Root Bridge Information 107
- Port Configuration 109
- DHCP Relay & Option 82 111
- Per Port Configuration 114
- Access Control List 115
- Users Configuration 118
- MAC Limit 121
- MAC Limit Port Status 122
- 802.1X Configuration 123
- System Configuration 125
- 802.1x Port Configuration 127
- Misc Configuration 128
- QoS Configuration 129
- QoS PerPort Configuration 132
- TOS/DSCP 133
- TOS/DSCP Configuration 134
- TOS/DSCP Port Configuration 134
- Power over Ethernet 136
- PoE Schedule 141
- CONSOLE MANAGEMENT 143
- Configure IP address 144
- Commands Level 146
- COMMAND LINE INTERFACE 147
- System Commands 148
- Switch Static Configuration 149
- Trunk Configuration 152
- VLAN Configuration 154
- VLAN Mode: Port-based 155
- Administration Configuration 159
- IP Configuration 160
- Reboot switch 161
- Reset to Default 161
- TFTP Update Firmware 161
- MAC limit 162
- Port Mirroring Configuration 163
- Quality of Service 164
- MAC Address Configuration 165
- STP/MSTP Commands 167
- System Options 172
- Community Strings 172
- Trap Managers 173
- 802.1x Protocol 175
- Non-Ipv4 ACL commands 178
- Binding 179
- Power over Ethernet Commands 180
- Configure PoE -- System 182
- Configure PoE -- Port 185
- (config)# poe priority low 1 186
- SWITCH OPERATION 188
- POWER OVER ETHERNET OVERVIEW 189
- The PoE Provision Process 190
- TROUBLE SHOOTING 193
- 10/100Mbps, 10/100Base-TX 194
Relacionado con productos y manuales para Accesorios de comunicación Interlogix NS2503-24P/2C User Manual
Accesorios de comunicación Interlogix NS3502-8P-2S Installation Guide Manual de usuario
(15 paginas)
(15 paginas)
Accesorios de comunicación Interlogix GE-DSSG-244-POE Installation Guide Manual de usuario
(10 paginas)
(10 paginas)
Accesorios de comunicación Interlogix NS4702-24P-4S-4X Command Line Guide Manual de usuario
(434 paginas)
(434 paginas)
Accesorios de comunicación Interlogix GE-DSH-73 Series Installation Sheet Manual de usuario
(13 paginas)
(13 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales