Interlogix NS2503-24P/2C User Manual Manual de usuario Pagina 131
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
NS2503-24P/2C User Manual
131
The table includes the following fields:
Object Description
First Come First Service The sequence of packets sent is based on arrival order.
All High before Low The high priority packets sent before low priority packets.
Weighted Round Robin
Select the preference given to packets in the switch's higher-priority queue.
These options represent the number of higher priority packets sent before one
lower priority packet is sent.
For example, 8 Highest : 4 SecHigh : 2 SecLow : 1 Lowest means that the switch
sends 8 highest priority packets before sending 4 second high priority packet,
before sending 2 second low priority packet, before sending 1 lowest priority
packet.
802.1p priority [0-7] Set up the COS priority level 0~7—High, Middle, Low, Lowest.
Apply: Press this button for changes to take affect.
Default: Press this button to reset QoS setting to default mode.
Help: Provide help information of QoS Configuration.
802.1p Priority: Priority classifiers of the Switch forward packet. COS range is from 0 to 7.
Seven is the highest class, and zero is the lowest class. The user may configure the
mapping between COS and Traffic classifiers.
- IFS NS2503-24P/2C User 1
- TABLE OF CONTENTS 3
- Introduction 8
- How to Use This Manual 10
- Product Features 11
- Product Specification 13
- INSTALLATION 15
- LED Indications 16
- Switch Rear Panel 18
- Install the Switch 19
- Rack Mounting 20
- SWITCH MANAGEMENT 23
- Management Access Overview 24
- Web Management 25
- Administration Console 26
- Protocols 28
- Web-Based Management 29
- Requirements 30
- Main WEB PAGE 32
- System Information 35
- Misc Config 36
- Console Port Info 40
- SNMP Configuration 41
- SNMPv3 Groups 44
- SNMPv3 View 45
- SNMPv3 Access 46
- SNMP V3 usm-user 48
- Syslog Setting 49
- System Log 50
- SNTP Setting 51
- Firmware Upgrade 52
- HTTP Firmware Upgrade 53
- Configuration Backup 54
- TFTP Backup Configuration 55
- Factory Default 56
- System Reboot 56
- Rate Control 59
- Port Status 60
- Port Statistics 61
- Port Sniffer 62
- Protect Port 64
- Remote Ping 65
- VLAN configuration 66
- Port VLAN ID 67
- Default VLANs 67
- Static VLAN Configuration 68
- Port-based VLAN 69
- 802.1Q VLAN 71
- VLAN Group Configuration 72
- VLAN Filter 75
- GVRP VLAN 76
- GVRP Setting 77
- GVRP Table 78
- Q-in-Q VLAN 79
- Q-in-Q Port Setting 80
- Q-in-Q Tunnel Setting 81
- To configure QinQ Port 81
- Trunking 82
- Aggregator setting 83
- Aggregator Information 84
- LACP enabled 85
- Switch 1 configuration 85
- Switch 2 configuration 86
- State Activity 88
- Forwarding and Filtering 89
- Static MAC Table 90
- MAC Filtering 91
- IGMP Snooping 92
- IGMP Configuration 96
- Static Multicast Table 98
- Spanning Tree Protocol 100
- NS2503-24P/2C User Manual 101
- Illustration of STP 103
- STP Parameters 104
- STP System Configuration 105
- Root Bridge Information 107
- Port Configuration 109
- DHCP Relay & Option 82 111
- Per Port Configuration 114
- Access Control List 115
- Users Configuration 118
- MAC Limit 121
- MAC Limit Port Status 122
- 802.1X Configuration 123
- System Configuration 125
- 802.1x Port Configuration 127
- Misc Configuration 128
- QoS Configuration 129
- QoS PerPort Configuration 132
- TOS/DSCP 133
- TOS/DSCP Configuration 134
- TOS/DSCP Port Configuration 134
- Power over Ethernet 136
- PoE Schedule 141
- CONSOLE MANAGEMENT 143
- Configure IP address 144
- Commands Level 146
- COMMAND LINE INTERFACE 147
- System Commands 148
- Switch Static Configuration 149
- Trunk Configuration 152
- VLAN Configuration 154
- VLAN Mode: Port-based 155
- Administration Configuration 159
- IP Configuration 160
- Reboot switch 161
- Reset to Default 161
- TFTP Update Firmware 161
- MAC limit 162
- Port Mirroring Configuration 163
- Quality of Service 164
- MAC Address Configuration 165
- STP/MSTP Commands 167
- System Options 172
- Community Strings 172
- Trap Managers 173
- 802.1x Protocol 175
- Non-Ipv4 ACL commands 178
- Binding 179
- Power over Ethernet Commands 180
- Configure PoE -- System 182
- Configure PoE -- Port 185
- (config)# poe priority low 1 186
- SWITCH OPERATION 188
- POWER OVER ETHERNET OVERVIEW 189
- The PoE Provision Process 190
- TROUBLE SHOOTING 193
- 10/100Mbps, 10/100Base-TX 194
Relacionado con productos y manuales para Accesorios de comunicación Interlogix NS2503-24P/2C User Manual
Accesorios de comunicación Interlogix NS3502-8P-2S Installation Guide Manual de usuario
(15 paginas)
(15 paginas)
Accesorios de comunicación Interlogix GE-DSSG-244-POE Installation Guide Manual de usuario
(10 paginas)
(10 paginas)
Accesorios de comunicación Interlogix NS4702-24P-4S-4X Command Line Guide Manual de usuario
(434 paginas)
(434 paginas)
Accesorios de comunicación Interlogix GE-DSH-73 Series Installation Sheet Manual de usuario
(13 paginas)
(13 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales