Interlogix EV1116 Manual de usuario descargar pdf (Pagina 5)

P/N 146251999-4 (ML) • REV D • ISS 12MAR13 5 / 32

SW 5: Setting LEDs

On: Enables both LEDs on the detector at all times (factory

default).

Off: Puts both LEDs under the control of the Walk Test and

Day/Night input. This activates the memory feature of the

detector.

LED indication

PIR Red LED Alarm relay To reset

Start up

Closed Automatically after 25 s

Low voltage

Open (Alarm) Apply correct voltage

PIR intruder

alarm

Open (Alarm) Automatically after 3 s

PIR/AM Red

LED

Yellow

LED

Alarm

relay

To reset

Start up

Closed Closed Automatically

after 60 s

Low voltage

Open

(Alarm)

Open

(Alarm)

Apply correct

voltage

PIR intruder

alarm

Open

(Alarm)

Automatically

after 3 s

Latched PIR

(Memory)

Switch to Night

mode

AM alarm

Open*

(Alarm)

Open

(Alarm)

See DIP

switch 3

After AM reset

Switch to

Night mode

Technical fault

Open

(Alarm)

Do a successful

walk test

Continuously on Normal blinking (1 Hz)

Fast blinking (4 Hz)

* Depends on the setting of the DIP switch SW4.

Specifications

EV1116 EV1116AM

Detector PIR PIR + AM

Signal processing DSP

Range 16 m

Optical 11 high-density mirror curtains

Memory Yes

Input power

For UL installations

9 to 15 VDC (12 V nominal)

10 to 15 VDC (12 V nominal)

Peak-to-peak ripple 2 V (at 12 VDC)

Detector start-up time 25 s 60 s

Normal current

For UL installations

5.5 mA

0.0528 mW

10 mA

—

Current in Alarm 2.5 mA 3.8 mA

Maximum current

(LED on)

11.5 mA 24 mA

Mounting height 1.8 m to 3.0 m (5.9 ft. to 9.8 ft.)

Target speed range 30 cm/s to 3 m/s

(1 ft./s to 10 ft./s)

20 cm/s to 3 m/s

(0.65 ft./s to

10 ft./s)

Alarm (NC) / Tamper relay

characteristic

80 mA 30 VDC, resistive

EV1116 EV1116AM

Pry-off tamper (not

evaluated by UL/cUL)

Optional On-board (Yes)

AM relay characteristic — 80 mA at 30 VDC

max., resistive

PIR alarm time 3 s

Operating temperature

For UL installations

−10 to +55°C (14 to 130°F)

0 to 49°C (32 to 120°F)

Dimensions (H x W x D) 125 × 55 × 60 mm

(4.92 x 2.16 x

2.36 in.)

125 × 65 × 60 mm

(4.92 x 2.6 x

2.36 in.)

Relative humidity 95% max. noncondencing

(UL Installations)

Weight 150 g

IP/IK rating IP30 IK02

Regulatory information

Manufacturer UTC Fire & Security Americas Corporation, Inc.

1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

UL The product must be connected to a listed burglar

system compatible control unit or power supply unit,

which provides a minimum 4 hours of standby power

and has a voltage output between 10 and 15 VDC.

All wiring must be made according to National

Electrical Code, NFPA70, and CSA C22.1, Canadian

Electrical Code Part I, Safety Standards for Electrical

Installations.

Perform walk test at least one per year.

Use only a listed power-limited supply.

EV1116AM has not been evaluated by UL.

FCC Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment

and receiver

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected

• Consult the dealer or an experienced radio/TV

technician for help

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

1 2 3 4 5 6 7 8 9 10 ... 31 32

Comentarios a estos manuales

Sin comentarios

Interlogix EV1116 Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Interlogix EV1116