Interlogix NS3550-8T-2S User Manual Manual de usuario Pagina 391
- Pagina / 495
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
User’s Manual of NS3550-8T-2S
391
Example:
Enable STP function on port1
NS3550-8T-2S:/>stp port mode 1 enable
STP Port Edge
Description:
Set or show the STP adminEdge port parameter.
Syntax:
STP Port Edge [<port_list>] [enable|disable]
Parameters:
<port_list>: Port list or 'all', default: All ports
Enable : Configure MSTP adminEdge to Edge
Disable : Configure MSTP adminEdge to Non-edge
Default:
disable
Example:
Enable STP edge function on port1
NS3550-8T-2S:/>stp port edge 1 enable
STP Port AutoEdge
Description:
Set or show the STP autoEdge port parameter.
Syntax:
STP Port AutoEdge [<port_list>] [enable|disable]
Parameters:
<port_list>: Port list or 'all', default: All ports
Enable : Enable MSTP autoEdge
Disable : Disable MSTP autoEdge
Default:
enable
Example:
Disable STP edge function on port1
NS3550-8T-2S:/>stp port autoedge 1 disable
STP Port P2P
Description:
Set or show the STP point2point port parameter.
Syntax:
STP Port P2P [<port_list>] [enable|disable|auto]
Parameters:
<port_list>: Port list or 'all', default: All ports
enable : Enable MSTP point2point
disable : Disable MSTP point2point
auto : Automatic MSTP point2point detection
- IFS NS3550-8T-2S 1
- User Manual 1
- TABLE OF CONTENTS 3
- 1. INTRODUCTION 15
- 1.2 Product Description 16
- 1.3 How to Use This Manual 17
- 1.4 Product Features 18
- 1.5 Product Specifications 21
- 2. INSTALLATION 23
- 2.1.2 Front Panel 24
- 2.1.3 LED Indicators 25
- 2.1.4 Switch Upper Panel 26
- 2.2.1 Installation Steps 27
- 2.2.2 DIN-Rail Mounting 28
- 2.3 Wiring the Power Inputs 31
- 2.5 Cabling 31
- 2.5.2 Removing the Module 34
- 3. SWITCH MANAGEMENT 36
- 3.3 Remote Telnet 38
- 3.4 Web Management 39
- 4. WEB CONFIGURATION 41
- 4.1 Main Web Page 44
- 4.2 System 46
- 4.2.1 System Information 47
- 4.2.2 IP Configuration 47
- 4.2.3 IPv6 Configuration 48
- 4.2.4 Users Configuration 49
- Add / Edit User 50
- 4.2.5 Privilege Levels 51
- 4.2.6 NTP Configuration 54
- 4.2.7 UPnP 54
- 4.2.8 DHCP Relay 56
- 4.2.9 DHCP Relay Statistics 57
- 4.2.10 CPU Load 59
- 4.2.11 System Log 60
- 4.2.12 Detailed Log 60
- 4.2.13 Remote Syslog 62
- 4.2.14 SMTP Configuration 63
- 4.2.15 EEE Power Reduction 64
- 4.2.16 Web Firmware Upgrade 65
- 4.2.17 TFTP Firmware Upgrade 65
- 4.2.18 Configuration Backup 66
- 4.2.19 Configuration Upload 68
- 4.2.20 Image Select 69
- 4.2.21 Factory Default 71
- 4.2.22 System Reboot 72
- 4.2.23 Daylight Saving 73
- 4.3.1 SNMP Overview 75
- 4.3.4 SNMPv3 Configuration 79
- 4.4 Port Management 83
- 4.4.3 Port Statistics Detail 86
- 4.4.4 SFP Information 87
- 1000Base-SX 88
- 1000Base-LX 88
- 100Base-FX 88
- 4.4.5 Port Mirror 89
- Mirror Port Configuration 90
- 4.5 Link Aggregation 91
- 4.5.1 Static Aggregation 92
- 4.5.2 LACP Configuration 94
- 4.5.3 LACP System Status 95
- 4.5.4 LACP Port Status 95
- 4.5.5 LACP Port Statistics 96
- 4.6 VLAN 98
- 4.6.3 VLAN Basic Information 100
- 4.6.5 VLAN Membership 105
- 4.6.6 VLAN Membership Status 106
- 4.6.7 VLAN Port Status 107
- 4.6.8 Private VLAN 107
- 4.6.9 Port Isolation 109
- 4.6.10 VLAN setting example: 111
- 4.6.11 MAC-based VLAN 116
- 4.6.12 MAC-based VLAN Status 118
- 4.6.13 Protocol-based VLAN 119
- : Click to save changes 120
- Auto-refresh 120
- 4.7 Spanning Tree Protocol 121
- 4.7.3 Bridge Status 128
- * means to select all ports 130
- * means all MSTI items will 133
- 4.7.6 MSTI Configuration 134
- Configuration Identification 135
- MSTI Mapping 135
- MSTI Port Configuration 136
- MSTx MSTI Port Configuration 136
- 4.7.8 Port Status 137
- 4.7.9 Port Statistics 138
- 4.8 Multicast 139
- Type Response Time 141
- 4.8.5 IGMP Snooping Status 147
- 4.8.6 IGMP Group Information 147
- 4.8.7 IGMPv3 Information 149
- 4.8.11 MLD Snooping Status 153
- 4.8.13 MLDv2 Information 155
- 4.8.14 MVR 155
- 4.8.15 MVR Status 157
- 4.8.17 MVR SFM Information 159
- 4.9 Quality of Service 160
- * means selection all 161
- 4.9.3 Port Classification 162
- 4-9-3 appears 163
- 4.9.4 Port Scheduler 164
- 4.9.5 Port Shaping 164
- 4.9.6 Port Tag Remarking 167
- 4.9.8 DSCP-Based QoS 171
- 4.9.9 DSCP Translation 172
- 4.9.10 DSCP Classification 174
- 4.9.11 QoS Control List 174
- 4.9.12 QoS Status 177
- 4.9.14 QoS Statistics 180
- 4.10 Access Control Lists 183
- 4.10.3 ACE Configuration 187
- MAC Parameters 189
- VLAN Parameters 189
- ARP Parameters 189
- IP Parameters 190
- Ethernet Type Parameters 192
- 4.11 Authentication 196
- MAC-based Auth 205
- Port State 213
- 4.11.7 RADIUS Overview 216
- 4.11.8 RADIUS Details 218
- RADIUS Accounting Servers 221
- Figure 4-11-21 230
- 4.12 Security 231
- 4.12.2 Access Management 234
- 4.12.4 HTTPs 236
- 4.12.5 SSH 237
- 4.12.6 Port Security Status 238
- 4.12.7 Port Security Detail 240
- 4.12.8 DHCP Snooping 240
- 4.12.12 ARP Inspection 246
- 4.13 MAC Address Table 248
- Dynamic MAC Table 250
- Navigating the MAC Table 250
- 4.14 LLDP 253
- 4.14.2 LLDP Configuration 254
- Civic Address Location 258
- Port Policies Configuration 260
- 4.14.4 LLDP-MED Neighbor 262
- 4.14.5 Neighbor 264
- 4.14.6 Port Statistics 266
- Local Counters 267
- 4.15 Diagnostics 269
- 4.15.1 Ping 270
- 4.15.2 IPv6 Ping 271
- 4.15.3 Remote IP Ping Test 272
- 4.15.4 Cable Diagnostics 272
- 4.16 Loop Protection 274
- 4.16.2 Status 275
- 4.17 RMON 276
- 4.17.2 RMON Alarm Details 277
- 4.17.3 RMON Alarm Status 278
- 4.17.5 RMON Event Details 280
- 4.17.6 RMON Event Status 281
- 4.17.8 RMON History Details 283
- 4.17.9 RMON History Status 284
- 4.18 Precision Time Protocol 289
- 4.18.2 PTP Status 291
- 4.19 Ring 292
- 4.19.5 Ring Wizard 301
- 4.19.6 Ring Wizard Example: 302
- 5. COMMAND LINE INTERFACE 304
- 6. COMMAND LINE MODE 305
- 6.1 System Command 306
- System Timezone 310
- Example: 310
- System Log Lookup 310
- 6.2 IP Command 311
- Default Setting: 316
- 6.7 Security Command 335
- Security Network ACL Delete 371
- Security AAA Timeout 381
- STP MSTI Port Configuration 394
- 6.9 Link Aggregation Command 395
- Aggregation Lookup 397
- Aggregation Mode 397
- 6.11 LLDP Command 401
- 6.12 LLDPMED Command 404
- LLDPMED Fast 408
- LLDPMED Info 408
- 6.13 EEE Command 409
- 6.14 Thermal Command 410
- QoS Port DSCP Translation 420
- QoS Storm Multicast 424
- QoS QCL Add 424
- QoS QCL Status 426
- QoS QCL Refresh 427
- 6.16 Mirror Command 428
- 6.17 Configuration Command 429
- 6.18 Firmware Command 430
- 6.19 UPnP Command 430
- 6.20 MVR Command 432
- 6.21 Voice VLAN Command 435
- 6.22 Loop Protect Command 441
- Loop Protect Transmit 442
- Loop Protect Shutdown 442
- 6.23 IPMC Command 443
- 6.25 SMTP Command 452
- SMTP Auth_user 454
- SMTP Auth_pass 454
- SMTP Mailfrom 454
- 6.30 PTP Command 471
- PTP OnePpsAction 477
- 7. SWITCH OPERATION 478
- 7.5 Auto-Negotiation 479
- 8. TROUBLE SHOOTING 480
- APPENDEX A 482
- 12345678 483
- APPENDEX B : GLOSSARY 484
Relacionado con productos y manuales para Accesorios de comunicación Interlogix NS3550-8T-2S User Manual
(631 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales