Interlogix EV1012 Manual de usuario descargar pdf (Pagina 5)

P/N 146169999-10 • REV C • ISS 02APR12 5 / 36

circuitry cannot return to its original reference levels, then

either the detector is still masked or possibly has been

damaged. The owner should then visually check that the

detector is still fully functional.

On: Resets the AM or TF status 40 seconds after a PIR alarm.

Off: Resets the AM or TF status after a PIR alarm when the

system is in Day and Walk Test status. The yellow LED will

blink quickly. When the system is in Night status, the yellow

LED will turn off and the system is reset (default).

SW 4: Signaling AM or TF output

On: Signals AM on both the AM and Alarm relays. Signals TF

on the AM relay only (EN 50131).

Off: Signals AM and TF on the AM relay (default).

SW 5: Setting LEDs

On: Enables both LEDs on the detector at all times (default).

Off: Puts both LEDs under the control of the Walk Test and

Day/Night input. This activates the memory feature of the

detector.

Configuring the coverage pattern

• Remove blinders (Figure 8, item 1) if necessary. The

modified pattern is shown in Figure 8, items 3 to 7.

Note: If both blinders are installed, the detector range is

limited to 6 m (default).

• Modify the pattern by breaking out blinder parts (shown as

gray in Figure 8, item 1). The corresponding curtain

fragments are shown in Figure 8, item 2.

• Put the appropriate mirror stickers if necessary. See

Figure 6, item 1 for details.

Caution: Removing stickers can damage the mirror

surface.

• When near objects directly under the detector, fit the mask

to the inside of the window (default). This disables the part

of the curtains looking down at the object, whose

closeness might destabilize the detector. See Figure 6,

item 2.

LED indication

PIR Red LED Alarm relay To reset

Start up

Closed Automatically after 25 s

Low voltage

Open (Alarm) Apply correct voltage

PIR intruder

alarm

Open (Alarm) Automatically after 3 s

PIR/AM Red

LED

Yellow

LED

Alarm

relay

To reset

Start up

Closed Closed Automatically

after 60 s

Low voltage

Open

(Alarm)

Open

(Alarm)

Apply correct

voltage

PIR intruder

alarm

Open

(Alarm)

Automatically

after 3 s

Latched PIR

(Memory)

Switch to Night

mode

PIR/AM Red

LED

Yellow

LED

Alarm

relay

To reset

AM alarm

Open*

(Alarm)

Open

(Alarm)

See DIP

switch 3

After AM

reset

Switch to Night

mode

Technical

fault

Open

(Alarm)

Do a successful

walk test

* Depends on the setting of the DIP switch SW4.

Continuously on Normal blinking (1 Hz) Fast (4 Hz)

Specifications

EV1012 EV1012AM

Detector PIR PIR + AM

Signal processing DSP

Range 12 m

Optical 9 high-density mirror curtains

Memory No Yes

Input power

For UL/cUL installations

9 to 15 V (12 V nominal)

10 to 15 V (12 V nominal)

Peak-to-peak ripple 2 V (at 12 V)

Detector start-up time 25 s 60 s

Normal current

consumption

For UL/cUL installations

4.4 mA

0.0528 W

10 mA

—

Current consumption in

alarm

1.2 mA 3.8 mA

Maximum current

consumption

11 mA 24 mA

Mounting height 1.8 m to 3.0 m (5.90 ft. to 9.84 ft.)

Target speed range 30 cm/s to 3 m/s

(1 ft./s to 10 ft./s)

20 cm/s to 3 m/s

(8 in./s to 10 ft./s)

Alarm (NC) / Tamper

relay characteristic

80 mA

30 V, resistive

80 mA

30 V

Pry-off tamper (not

evaluated by UL/cUL)

N/A Onboard (yes)

AM relay characteristic — 80 mA at 30 V max.

Alarm time 3 s

Operating temperature

For UL/cUL installations

−10 to +55°C (14 to 130°F)

0 to 49°C ( 32 to 120°F )

Dimensions (H x W x D) 108 × 60 × 46 mm (4.25 × 2.36 × 1.81 in.)

Relative humidity 95% max. noncondensing

(UL/cUL installations)

Weight 120 g (4.2 oz.) 128 g (4.5 oz.)

IP/IK rating IP30 IK02

Regulatory information

Manufacturer UTC Fire & Security Americas Corporation, Inc.

1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, Netherlands

Certification

1 2 3 4 5 6 7 8 9 10 ... 35 36

Comentarios a estos manuales

Sin comentarios

Interlogix EV1012 Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Interlogix EV1012